Blog | Advanced Geosciences Inc

Detecting Karst At Friesenhahn Cave Using 3D Electrical Resistivity

Posted by markus on Янв 12, 2017

Dr. Keith N. Muhlestein, PG, REM, from the University of Texas at San Antonio’s Environmental Science and Engineering department, used AGI equipment for an electrical resistivity survey to image Karst regions within Friesenhahn Cave in Texas. 

Background

Friesenhahn Cave is located near the Balcones Escarpment along the Edwards Plateau of central Texas in northern Bexar County. It is well known as a Pleistocene epoch predator cave. It contains an exceptional variety of megafauna fossils including ...

2D Resistivity Surveys: The Benefits, Limitations, & Technology

Posted by markus on Янв 04, 2017

In the 1980s and early 1990s, geophysicists became largely disenchanted with electrical resistivity because of the inadequacies of Vertical Electrical Sounding (VES). Specifically, the VES method assumes that the imaged geology is horizontally layered and that each layer is homogeneous. Of course, this often isn’t the case, causing some project managers (and their clients) to become fed up with the unusable results.

Around this time, we created the Sting R1—the industry’s first 2D electrical resistivity imaging instrument—and tested the instrument on what is now called ...

1D Geophysical Resistivity Survey: Vertical Electrical Sounding

Posted by markus on Дек 16, 2016

Throughout most of the 20th century, Vertical Electrical Sounding (VES) was the dominant geophysical resistivity method. It has been used all over the world for three primary purposes: geotechnical investigation, groundwater exploration, and mineral exploration. VES is performed using either the Wenner electrode configuration described in the ASTM G57 standard or using the Schlumberger electrode configuration. (The Schlumberger method is most commonly used for groundwater and mineral exploration, because it is less labor intensive than the Wenner method.)

Below, we’ll describe VES’s...

In-Depth Descriptions Of 3 Soil Resistivity Testing Techniques

Posted by markus on Ноя 22, 2016

Soil resistivity testing is performed for a variety of important applications, including:

  • Testing grounding grids: Grounding grids are primarily used in industrial settings—like electrical substations—where expensive machinery needs to be protected. The U.S. National Electric Code sets forth that every substation must have at least one grounding rod to protect equipment from lightning damage and to ensure that a stray current from the neutral doesn’t electrocute a person nearby.
  • Cathodic protection: Cathodic protection is a way to protect underground or...

Determining Groundbed Location For Cathodic Protection: What You Need To Know

Posted by markus on Ноя 17, 2016

Cathodic protection is a method used to reduce steel oxidation through an electrochemical process. Cathodic protection is used to protect buried or submerged pipelines, bridges, and large steel structures from corrosion, breakdown, and rust when an electrolyte (like water with salt and minerals) is present. The electrolyte serves as a conduit for the electron flow from the anode to the cathode. In steel structures where no electrolyte is present (like a steel building), they are best protected by galvanizing (zinc coating) or simply painting. 

For small steel structures, anode...

The Exploration Of Aggregate Materials Using Geotechnical Techniques

Posted by markus on Ноя 16, 2016

Aggregate materials—like sand, gravel, crushed stone, slag, and recycled concrete—provide bulk and strength to concrete or asphalt. Large aggregate quarries and sand and gravel pits are located around most populated areas because of the high cost of transporting aggregate. (In fact, the cost of transportation from the mine to the consumer may even be higher than the actual cost of the aggregate.)

There are many different types of aggregate materials found in various geographic locations:

  • Alluvial deposits are clay, sand and gravel beds deposited by flowing water. These...

When & Why To Use ASTM G57 For Soil Testing

Posted by markus on Ноя 15, 2016

The ASTM G57 standard (also known as the four-pin Wenner method) is used to determine the properties of soil. 

Soil tests can be performed in many ways and for a number of reasons.

  • In agricultural applications, a soil test may be useful for analyzing nutrients and moisture content.
  • In environmental analysis, soil testing is used to detect hazardous material present in the ground.
  • In geotechnical investigations, soil tests may involve cone penetrometer tests to examine certain soil properties.
  • In laboratory settings, soil tests are performed to...

Behind The Scenes Of Groundwater Exploration With Electrical Resistivity

Posted by markus on Ноя 14, 2016

Early Methods Of Groundwater Exploration

To best understand how electrical resistivity surveys for groundwater exploration work today, it’s important to understand where resistivity testing began. 

Brothers Conrad and Marcel Schlumberger performed the very first investigation of how electrical current moves through the ground and what you can detect using an electrical resistivity survey in the early 1900s. From their research came what is now one of the most common methods of groundwater exploration, vertical electrical sounding (VES).

VES uses four electrodes...

Marine Resistivity Surveys: Breaking Down The Benefits & Use Cases

Posted by markus on Ноя 10, 2016

Having an accurate image of the subsurface beneath a body of water is beneficial in myriad use cases, including: 

  • Determining sub-bottom geology for dredging purposes or communication cable lay-out.
  • Monitoring leakage or mapping sediments in a dam.
  • Mapping freshwater and saltwater interfaces near shorelines or offshore.
  • Characterizing estuary boundaries.
  • Measuring water column salinity variations.
  • Mapping underwater mineral exploration.
  • Locating freshwater springs at sea.
  • Determining sediment load (dredging survey...

An Overview Of The IEEE Standard 81 Fall-Of-Potential Grounding Test

Posted by markus on Сен 28, 2016

The Institute of Electrical and Electronics Engineers (IEEE) Standard 81-2012 “Guide for Measuring Earth Resistivity, Ground Impedance, and Earth Surface Potentials of a Grounding System”, suggests the fall-of-potential grounding test to be used to evaluate the capacity of an electrical grounding system—it is often used by subcontractors to power engineers. 

Why is the IEEE Standard 81 fall-of-potential grounding test important?

Grounding tests are mainly used at lightning protection systems, electrical substations, and industrial sites where expensive machinery needs to be...

Страницы